Customizable Rf Power Amplifiers GF100W300-400MHz Lora GaN Module Anti-drone Module Built-in VCO

Product Overview

This QHXK RF power amplifier module is listed as Customizable Rf Power Amplifiers GF100W300-400MHz Lora GaN Module Anti-drone Module Built-in VCO. The stated frequency range is 300–400 MHz. The specifications below are taken from the supplied product listing and should be confirmed against the current datasheet before integration.

Key Specifications

• Frequency range: 300–400 MHz
• Gain: 50dB
• Supply voltage: 28V
• Connector / mounting: N-K
• Manufacturer part number: GF-100W300-400MHz

System Integration

For 300–400 MHz RF power amplifier module, confirm the required input signal level, supply conditions, RF connectors, mechanical fit and thermal management with the host system. Values not listed above should be checked with QHXK before design approval.

Application and Technical Support

This module is offered for integration into compatible RF equipment. Application suitability depends on the operating band, system design and applicable regulations. Contact QHXK to request the detailed datasheet and discuss interface or customization requirements.

Product selection: 300–400 MHz

The GF100W300-400MHz listing is intended as a starting point for projects reviewing comparing a mid-range lower-band configuration. The stated band for this model is 300–400 MHz. Confirm that the complete project requirement fits the exact model under consideration; do not infer performance beyond the information published for this product. The product listing and model reference identify the item, while the current datasheet should be used to verify detailed operating limits and guaranteed performance.

The GF100W300-400MHz model is listed for 300–400 MHz. When considering it for an OEM design, compare the complete project frequency requirement with this exact range and obtain the latest supplier documentation. The product should not be selected solely because its model name resembles another item in the same family; each configuration needs its own review.

A structured RF component review should capture the required band, the intended signal-chain position, connector and interface requirements, available DC power, mechanical envelope and cooling arrangement. It should also record any environmental conditions, acceptance criteria or documentation needed by the project. Sending these details together with the model reference gives the supplier a clearer basis for confirming the requested configuration.

The QHXK catalogue also lists 200–300 MHz and 200–400 MHz alternatives. Those pages are useful for a first comparison, but final selection should be based on the current datasheet and the project’s approved requirements.

Information to prepare for a configuration review

• The exact model reference and required frequency range.
• The intended equipment interface and RF connector requirements.
• The available DC supply interface and installation constraints.
• The mechanical envelope, mounting details and cooling provisions.
• The operating environment, expected quantity and any required qualification documents.

Frequently asked questions

Should I choose this model based on a nominal center frequency?

No. Compare the full required frequency span with the listed range and verify the guaranteed data in the exact model’s datasheet.

Can two models with overlapping ranges be considered equivalent?

Not without a documented comparison. Check the datasheets, interfaces and revision details, and ask QHXK to confirm any proposed substitution.

Which document should be used for final technical approval?

Use the latest controlled datasheet and mechanical drawing for the exact model and revision. Ask QHXK to clarify any requirement that is not covered by the published documentation.

Related models

For comparison, review G100W200-300MHz RF power amplifier module and GF100W200-400MHz RF power amplifier module. The stated bands and model references differ; use each product’s own documentation when comparing candidates.

Documentation for engineering approval

Before a module is approved for an OEM assembly, request the latest datasheet and mechanical drawing for the exact model. Review the documented RF and DC interfaces, mounting details, thermal instructions, operating limits and product revision with the responsible engineering team. Keep the supplier’s controlled documents with the project record so the quoted and approved configuration can be traced.

QHXK’s GaN RF power amplifier module portfolio and custom RF power amplifier design and manufacturing pages provide further product-family context. For model-specific documentation, configuration questions or a quotation, contact QHXK.

Any RF equipment must be evaluated and operated only within applicable laws, spectrum authorizations and site permissions. Product availability does not itself authorize radio transmission or deployment.